To reset the password for a Hi Sharp or generic Sharp DVR, you can use built-in recovery options like dynamic codes, official support tools, or physical hardware resets. 🔑 Common Default Credentials Before performing a hard reset, try these common default login combinations: Username: admin or Admin Passwords: 123456 , admin , Admin , or just leave it blank . Other defaults: 111111 , 000000 , or 888888 . 🛠️ Method 1: Use the "Dynamic Code" (Official Method) Most modern Hi Sharp DVRs/NVRs include a "Forgot Password" feature on the login screen. Click Forgot Password on the login interface. Navigate to the Retrieve Password or Dynamic Code page. Take a photo of the dynamic code/QR code displayed on the screen. Send the photo, along with your model number and serial number , to Hi Sharp Support (sales@hisharp.com.tw) or your regional distributor. They will provide a temporary unlock code to reset your admin account. ⚡ Method 2: Physical Hardware Reset If you cannot access the menu, you can force a factory reset using the internal board. External Reset Button: Look for a small pinhole on the back or bottom. Press and hold with a paperclip for 5–30 seconds while the device is powered on. Internal Jumper: If there is no button, you may need to open the casing and locate two pins marked "RESET" or "CLR" . Turn off the power. Use a screwdriver to short the two pins (connect them). Power the unit back on while holding the short for 30 seconds. The DVR will beep or reboot to the setup wizard. 📱 Method 3: Mobile App Recovery If you previously linked your DVR to a mobile app like Hi Sharp EX or Superlive Plus: Open the app and go to Reset Device Password . Use the app's scanner to scan the QR Code from the DVR's login screen. You will receive a verification code via your registered email . Enter that code on the DVR to create a new password. 📌 Pro Tip: If your DVR is an older generic model (often labeled "H.264 Network DVR"), the master password might be generated based on the date shown on the screen . FAQ - Support | HI SHARP INTELLIGENCE
If you have forgotten the password for your Hi Sharp DVR/NVR , there are several standard methods for recovery depending on your specific hardware model and firmware version. 1. Default Login Credentials If your device is new or has been recently factory reset, try the manufacturer's default credentials. Default Username: admin Default Password: 123456 Alternative Default: On some models, the password may be the same as the username (e.g., admin / admin ). 2. Using the "Dynamic Code" (Recommended) This is the standard recovery method for most modern Hi Sharp units. Navigate to the Login Interface on your DVR. Select "Forgot Password" and then "Retrieve Password" . Click on the "Dynamic Code" page. Screenshot or take a photo of the dynamic code displayed on the screen. Email this photo, along with your device’s model number and serial number , to sales@hisharp.com.tw or your regional distributor. They will provide a temporary password to unlock the unit. 3. QR Code Recovery If you previously bound an email address to the device during initial setup: On the local login GUI, select "Forgot Password" . Select the QR Code or Email Verification option. Scan the displayed QR code using the Hi Sharp mobile app (or similar compatible client). A verification code will be sent to your reserved email address . Enter this code into the DVR to create a new password. 4. Security Questions If you set up security questions during the first-time wizard: At the login screen, click "Forgot Password" . Choose "Question Verification" . Answer the three security questions correctly to gain access and reset your password. 5. Hardware Factory Reset If software methods fail, some models feature a physical reset button. Locate the Button: Look for a small "Reset" button on the motherboard inside the chassis or on the back panel. Action: Press and hold the reset button for approximately 30 seconds while the device is powered on to restore all settings, including the password, to factory defaults. Summary of Support Links Official Support: Hi Sharp FAQ Page Quick Guides: NVR/DVR Manuals FAQ - Support | HI SHARP INTELLIGENCE
To reset the password for your DVR (likely a HiLook, Hikvision, or Hi-Focus model based on your query), follow the method that matches your specific device: 1. HiLook or Hikvision DVRs Modern HiLook and Hikvision systems generally use a QR code reset method through their mobile apps. On the DVR Screen: Go to the login page and click "Forgot Password" Select Reset Method: "Verify by Hik-Connect" "Verify by HiLookVision" Scan QR Code: Open the corresponding app on your phone, go to "Reset Device Password" , and scan the QR code displayed on your monitor. Enter Code: You will receive a verification code in the app. Enter this code exactly (it is case-sensitive) on the DVR monitor to set a new password. 2. Hi-Focus DVRs If your device is a Hi-Focus model, you may need a dynamic password from technical support. Find Retrieve Option: At the login screen, enter as the username and click "Retrieve Password" Dynamic Password: "Dynamic Password" . You will see a set of details (often a date-based code) that you must share with Hi-Focus Technical Support to receive a one-time reset code. 3. Physical Hardware Reset If the software methods aren't available, check for a physical button. Reset Button: Look for a small pinhole or button on the back or inside the DVR casing. Hold to Reset: With the power on, press and hold the button for 5 to 30 seconds until the unit beeps or lights flash. The system will reboot to factory defaults. 4. Try Default Passwords If the DVR was recently factory reset, try the common default login: Techage.com , or leave it Techage.com Could you let me know the exact brand and model number found on the sticker of your DVR so I can give you the specific steps? How to Reset a NVR Without Password: Easy Guide - eufy US
To reset the password on a Hi Sharp DVR , you typically need to use their proprietary "IP Finder" software or a physical reset method. Because security protocols can vary by firmware version, here is the most effective process to follow: 1. Try Default Credentials Before performing a full reset, check if the device is still using factory settings. According to the Hi Sharp FAQ (or leave it blank) www.hisharp.com 2. Use the "IP Finder" Tool Hi Sharp provides a specific utility to manage their devices over a Local Area Network (LAN). software from the Hi Sharp Support Page Connect your PC to the same network as the DVR and run the software to locate the device. Look for a "Forgot Password" or "Reset" option within the tool. This often generates a temporary code or requires a QR code scan. 3. Hardware Reset (Physical) If you cannot access the software, a hard reset will revert the device to factory defaults: Locate the Reset Button: This is usually a small pinhole button on the back of the unit or occasionally on the motherboard inside the casing. The Procedure: Power off the DVR. Press and hold the While holding the button, power the DVR back on. Continue holding for 15–30 seconds until you hear a beep or see the status lights flash. 4. Technical Support "Super Password" If the above steps fail, you may need a dynamic "Super Password" based on the current date displayed on your DVR's monitor. exact date and time shown on the DVR screen. Contact your local distributor or Hi Sharp Technical Support with the device's Model Number Serial Number . They can provide a one-day master code to bypass the lock. Learn more FAQ - Support | HI SHARP INTELLIGENCE hi sharp dvr reset password upd
⚠️ Disclaimer: This information is for resetting a password on a device you own. Bypassing security on a device you do not own may be illegal. Proceed at your own risk.
Method 1: Use the Master Reset File (Most Common for Hi Sharp) Hi Sharp DVRs often use a factory backdoor method involving a reset.dav file. What you need:
A USB flash drive (FAT32 format, 2GB–16GB recommended) Computer with internet access The DVR's model number (on the back or in the menu) To reset the password for a Hi Sharp
Steps:
Download the reset file:
Search for: Hi Sharp reset.dav file or visit the official Hi Sharp support site. Alternatively, contact Hi Sharp support with your device model and serial number — they may email you the file. 🛠️ Method 1: Use the "Dynamic Code" (Official
Prepare the USB:
Format the USB drive to FAT32 . Copy the reset.dav file to the root (not inside any folder).
